Sper-scientific 850068 Hybrid Powered Environmental Meter Manual do Utilizador

Hybrid–Powered Environmental Quality Meter 850068 Instruction Manual

- 10 - KEY PAD Turns the unit on/off Freezes current measurement value Clears recorded min/max values Enters Record Mode Displays recorded min/

- 11 - POWER TYPE SELECTION Hybrid Power (Green) Selection 1. Slide the Power Type Switch up to the G position to use the meter’s Green power source

- 12 - POWER TYPE SELECTION Battery Power Selection 1. Ensure that you have correctly installed the 9V battery in the battery compartment. (Refer to

- 13 - MEASUREMENT PROCEDURES 5. Cover the light sensor to block any light from registering on the meter. Press ZERO to calibrate the meter to zero.

- 14 - MEASUREMENT PROCEDURES Air-Velocity Measurement 1. Ensuring correct pin alignment, insert the Anemometer plug into the PROBE IN Anemometer soc

- 15 - 6. Face the air-flow sensor (marked with a yellow dot) in the direction of the wind. 7. The meter measures the wind-speed and ambient tempera

- 16 - Relative Humidity Measurement 1. Press POWER to turn the meter on. 2. Continuously press FUNCTION until the meter displays the relative humidit

- 17 - Thermocouple Temperature Measurement This procedure requires an optional Type-K thermocouple probe. 1. Press POWER to turn the meter on. 2. En

- 18 - Hold Mode Selection 1. Press POWER to turn the meter on. 2. Using the FUNCTION button, select your desired measurement function (Light, Air-Vel

- 19 - Record Mode & Auto-Off Selection To save battery life, the Environmental Quality Meter turns off automatically after 10 minutes of inactivi

- 2 - Hybrid-Powered Environmental Quality Meter 850068 Copyright ©2009 by Sper Scientific ALL RIGHTS RESERVED Printed in the USA

- 20 - 3. To clear the max/min values and continue recording, press HOLD. The meter clears the previously recorded max/min values and enters Record

- 21 - Hands-Free Operation The Environmental Quality Meter includes both a built-in mini-easel and a tripod screw-mount for easy hands-free monitori

- 22 - BATTERY REPLACEMENT 1. If the meter displays the low battery icon , press POWER to turn the meter off. 2. Use a small Philips scr

- 23 - TROUBLESHOOTING No Display:  Ensure that you have pressed POWER for longer than 100mS.  Ensure that the batteries are in good condition, h

- 24 - SPECIFICATIONS General Specifications Size 6.7” (H) x 2.8” (W) x 1.5” (D) 170mm (H) x 70mm (W) x 39mm (D) Weight 15.2 oz. (432g) Excluding

- 25 - SPECIFICATIONS Anemometer Specifications Unit Range Resolution Accuracy ft/min 80 ~ 4930 ft/min 1 ft/min ≤20 m/S ±3% F.S. >20 m/S ±4% F.S

- 26 -  800060~77 Type-K Thermocouple Probes  840090 Water-Resistant Case  840092 Bench-Top Tripod  840093 Field Tripod OP

- 27 - ENVIRONMENT REFERENCES Refer to any of the following organizations for current and reliable data regarding recommended exposure limits for the

- 28 - Rev. 5/3/2012 WARRANTY Sper Scientific warrants this product against defects in materials and workmanship for five (5) years from the

- 3 - MATERIALS SUPPLIED ... 4 INTRODUCTION ... 5 FEATURES ...

- 4 - MATERIALS SUPPLIED  Meter  Anemometer Vane Probe  Water-Resistant Plastic Case  One DC 9V Battery  Instruction Manual

- 5 - The Sper Scientific Hybrid-Powered Environmental Quality Meter 850068 is a 4-in-1 instrument that functions as a:  Light Meter—measures light

- 6 - The rugged, light-weight and portable design of the Environmental Quality Meter allows you to use it almost anywhere to monitor elements and mai

- 7 -  Multi-Purpose 4-in-1 Meter  Hybrid-Power (Hand-Crank Generator)  Rugged, Light-Weight, and Portable  Accurate and Easy-to-Use  One-Bu

- 8 - UNIT DESCRIPTION Light Sensor Generator Hand-Crank (Bottom of Unit) Easel Stand (Back of Unit) LCD Display Key Pad Humidity Sensor (Top of Unit

- 9 - LCD DISPLAY Light–Level Measurement Units Lux Ft-cd x10 Both Lux and Ft-cd (Foot Candle) measure luminance. Lux = lumens per square meter. Ft-